Flight Controllers

We have many flight controllers listed below and it is hard to say which is the best for you. 

Omnibus F4

This flight controller features a F4 chip and betaflight OSD.  This enables you to access many of the settings via the OSD in the goggles to change things like PIDS and rates.  When paired with a VTX with Smart Audio, you can also change and view your video frequency.  These run Betaflight.  These feature a MPU6000 gyro.  These have SD card slots for blackbox data.

Omnibus F7

This flight controller features a F7 chip and betaflight OSD.  This enables you to access many of the settings via the OSD in goggles to change things like PIDS and rates.  When paired with a VTX with Smart Audio, you can also change and view your video frequency.  These run Betaflight. The F7 board features both a MPU6000 Gyro and 20689 gyro.  You can shoose which you would like to run.  The MPU6000 is limited to 8K, but has a better noise floor. The 20689 has a 32K gyro capable of 32 khz refresh rates.

RaceFlight Revolt

The Revolt was designed off the Open Pilot Revolution design. It features a F4 board and gyro capable of 32K Refresh rates.  These run Raceflight.  They have a very easy to use GUI.

FuryF3

The Fury F3 features an F3 chip and Betaflight OSD.   This enables you to access many of the settings via the OSD in goggles to change things like PIDS and rates.  When paired with a VTX with Smart Audio, you can also change and view your video frequency.  There is onboard memory for blackbox.  The FuryF3 was a joint venture between Kevin the original designer and Diatone to make a stable, quality board for their ARF series.  The FuryF3 uses JSt connections, but also has the tabs on the bottom side of the board if the JST connectors break.  These use the FuryF3OSD Betaflight firmware.

Items 1 to 10 of 18 total

Set Ascending Direction
per page

Grid  List 

Page:
  1. 1
  2. 2
  • GPS Module for Naze32 Tye Controllers

    This is a GPS module for a Naze32 flight controller. Please refer to either the Cleanflight or Baseflight manual for proper setup. Learn More

    Regular Price: $30.00

    Now only: $20.00

  • 6 Pin to 6 Pin Cable 50mm

    This is a 50mm long 6 pin to 6 pin connector. You get 1 per order. Learn More
    $1.00

  • DIY JST XH Pin Connector Set, A

    This is a DIY pin set. You get different JST XH pin connectors, wires and leads. One end of the cable has a small pin to fit in the multiple hole connector and the other end fits a Black connector. The black connectors would then fit well onto servo size pins. Learn More
    $6.00

  • 16 28 AWG Wire Set, B

    This is a set of 16 28AWG wires. They each have a black connector on each end that will fit over Flight controller and servo pins. Learn More
    $6.00

  • Omnibus F4 Flight Controller AIO V4 ACRO (Smart Audio Support)

    1 Review(s)
    The New V4 Omnibus F4 flight control packs a punch! This flight controller has a F4 processor for fast and reliable speed! This flight controller incorporates a onboard OSD running off the SPI so it does not used an UART. The PDB uses the MPU6000 Gyro which is the "gold standard" of all gyros! The onboard 5V 1.5A BEC can power your camera, receiver and WS2812 lights!

    Here is the best part! You can connect your TBS Unify Pro to an UART and enable Smart Audio. Now you can program your VTX via your OSD, channel, power snd frequency. This also works with the ImmersionRC Tramp.

    I forgot to mention you can also change pids in the field just as easily! No more need to bring your laptop!

    These do NOT include the wire to connect to the Typhoon ESC, please purchase 8 Pin to 8 Pin cable so you can connect to the ESC!

    Correct Firmware for V4 board

    > Learn More
    $34.99
    Expected First Week of May

  • Omnibus F4 PRO Flight Controller V3 Barometer(Smart Audio Support)

    1 Review(s)
    The New V2 Omnibus F4 Pro flight control packs a punch! This flight controller has a F4 processor for fast and reliable speed! This flight controller incorporates a onboard OSD running off the SPI so it does not used an UART. The PDB uses the MPU6000 Gyro which is the "gold standard" of all gyros! The onboard 5V 3A BEC can power your camera, receiver and WS2812 lights!

    Here is the best part! You can connect your TBS Unify Pro to an UART and enable Smart Audio. Now you can program your VTX via your OSD, channel, power snd frequency. This also works with the ImmersionRC Tramp.

    I forgot to mention you can also change pids in the field just as easily! No more need to bring your laptop!

    The main difference on this board is the built in current sensor so you can see current draw and total mAh used!

    Learn More

    Regular Price: $41.99

    Now only: $29.00

  • Asgard F4 FC PDB OSD and ESC

    2 Review(s)
    AIO(all in one) Flight Controller and 4 BLHELI_S ESC on one PCB! The mounting holes are 30.5 x 30.5mm. Not only do you get a F4 FC and 4 ESC's the board also has Betaflight OSD, SD Card, Current sensor and 5V BEC. The on board ESC supports DSHOT, use J_H_15 firmware.

    ESC tested under 3-4S, 2308 Motor 2300KV with 5045x3 props The actual current depends on the frame and air flow.

    Learn More
    $89.99

  • OMNIBUS F4 Nano v2

    A new generation AIO Flight control for FPV, based on F405 MCU, using F4 MCU controls OSD over SPI bus in DMA mode, OSD Configation has been incl. in Betaflight GUI. Supports SD Card and LIPO direct input (2-4S) MPU6000 at SPI bus. No Flash for blackbox function.

    These do NOT include the wire to connect to the Wave ESC, please purchase 8 Pin to 8 Pin cable so you can connect to the ESC!

    Learn More
    $35.99

  • Emax Babyhawk Femto F3 Flight Controller

    This is a replacement for the stock Emax Babyhawk F3 Flight controller. This is the Femto F3 flight controller for brushless motors. This tiny FC has a 3A 5V BEC to motor LEDs, your receiver and the FC! Great FC for micro builds. Learn More
    $28.04

  • 70-90mm Micro Bundle F4 FC and AIO Dshot ESC

    This is a bundle of the Ominbus Nano F4 with the Wave 4 in 1 ESC. This package was designed to work together on your micro builds. Included in the kit is a 8 pin connector to connect the FC and ESC together providing the ESC signals, ground, and Vbat. Here we have a bundle of the items you need to complete this project.

    Please select the items you would like. You must select both items to get both items.

    Learn More

    Starting at: $26.99

Items 1 to 10 of 18 total

Set Ascending Direction
per page

Grid  List 

Page:
  1. 1
  2. 2