Omnibus F4 Flight Controller AIO V5 with Barometer (Smart Audio Support)

The New V5 Omnibus F4 flight control packs a punch! This flight controller has a F4 processor for fast and reliable speed! This flight controller incorporates a onboard OSD running off the SPI so it does not used an UART. The PDB uses the MPU6000 Gyro which is the "gold standard" of all gyros! The onboard 5V 1.5A BEC can power your camera, receiver and WS2812 lights!

Here is the best part! You can connect your TBS Unify Pro to an UART and enable Smart Audio. Now you can program your VTX via your OSD, channel, power snd frequency. This also works with the ImmersionRC Tramp.

I forgot to mention you can also change pids in the field just as easily! No more need to bring your laptop!


These do NOT include the wire to connect to the Typhoon ESC, please purchase 8 Pin to 8 Pin cable so you can connect to the ESC!


Correct Firmware for V4 board

>
SKU: ABOBF4V5

Availability: In stock

$34.99
$34.99

Description

Details

Version 5 Changes

  • On v5, we added jumpers for Current source select, please read the manual and set the jumper before using the FC.
Version 4 Changes
  • 8 Pin Wire Harness JST plug for all 4 esc's, grnd, Vbatt, and current sensor from 4 in 1 ESC
  • SBUS moved to UART6
  • DSM to UART3 or 1
  • SBUS inverter controlled by software

    Some things to Note:

    • Betaflight is recommended.
    • The board comes pre-selected for SBUS, You do not need to solder the jumper, it is already done.
    • To power the board you have two options.
      • Connect battery directly to BAT/GND. This will provide power to the board as well as 5V to the Receiver Pins.
      • Supply 5V on one of the ESCs connections from a PDB. However you obviously want to have voltage display in your OSD so just connect BAT/GND to your LiPo (up to 4S).
    • To power your VTX and camera. Out of the box "RAM" is not connected to anything. That leaves you with following alternatives.
      • Solder connect RAM and VBAT to get LiPo voltage. This would be unfiltered and could cause video noise.
      • Short RAM and 5V to get filtered 5V from the board. This would provide clean video but 5V is not enough for most VTX on the market, so power your VTX from 12V PDB.
      • Provide clean voltage from external BEC . It will provide filtered 10V for HS1177 and a VTX.
    • To avoid issues with the OSD display, you must connect a ground from the Camera to the board AND a ground from the VTX to the board.

Additional Info

Features:
  • SPI Gyro MPU6000
  • On-Board OSD (controllered by Betaflight, FC over SPI bus)
  • MicroSD Blackbox
  • F4 Processor (F405)
  • 5v1.5a SBEC
  • On-Board Video Filter (only can supply 5V to VTX and Camera)
  • 3.3V for Spectrum Receivers
  • Barometer

Reviews

TipsReview by T_rell
Quality
Service
Value
Very pleased with this purchase:

Things to note with this flight controller:
-OOB the OSD was not working, flashing to the latest version resolved issue.
-When flashing this Flight Controller with BetaFlight make sure and select OMNIBUSF4SD, if you select OMNIBUSF4 instead you will lose the barometer function.
(Posted on 3/13/2017)

Write Your Own Review

You're reviewing: Omnibus F4 Flight Controller AIO V5 with Barometer (Smart Audio Support)

How do you rate this product? *

  1 Bone 2 Bones 3 Bones 4 Bones 5 Bones
Quality
Service
Value


  • + =

Why Buy From 2dogrc

Why Buy From 2dogrc

Most Products ship the SAME Day!

Have questions? Send us a quick email and we will get back to you fast!

High quality RC products from people who fly RC products!

Buy this product and earn Doggy Dollar loyalty points!