FrSky V8FR-II HV long range Taranis 8/16Ch Rx receiver NO Telemetry

Be the first to review this product

The V8 is a long Range non-telemtry receiver.

Binding Instructions

  • To make the two products to work, you need to put both of them in D8_mode.
  • -Set the Taranis in D8_mode from the set up page.
  • -Connect Ch1 & Ch2 signal pins of V8FR-II by provided jumper and then connect battery to it directly (no need to hold the F/S button on V8FR-II).

SKU: FRSKYV8

Availability: Out of stock

$28.00

Description

Details

Compatible with all FrSky modules (V8 & D), receive only (V8FR-II can talk in either mode, but it does not send telemetry information back to the transmitter).

This receiver is a NON-Telemtry 8 channel receiver for the Frsky systems.  


 

Range Check - You MUST do range checks - !  As part of your risk minimisation plan and duty of care

A pre-flight range check should be done before each flying session. Reflections from nearby metal fences, concrete buildings or tress can cause loss of signal both during range check and during the flight. Follow the steps below to perform the range check.

  1. Place the model at least 60cm (two feet) above non-metal contaminated ground (e.g. on a wooden bench).
  2. The receiver antennas should be separated in the model, and do not touch the ground.
  3. The module antenna should be in a vertical position.
  4. Turn on the transmitter and the receiver, press the F/S button on the XJT module for 4 seconds to enter range check mode, the RED LED will be off, GREEN LED will flash rapidly. The effective distance will be decreased to 1/30 (at least 30m).
  5. Walk away from the model while simultaneously operating the controls on the transmitter to confirm all controls’ normal operation.
  6. Press the F/S button on the XJT module for 1~2 seconds to exit range check mode, RED LED will be back on, indicating normal operation is back.
 

Binding Procedure

Binding is the process of uniquely associating a particular receiver to a transmitter module sometimes called model-matching or model-pairing. A transmitter module can be bound to multiple receivers (not to be used simultaneously). A receiver can only be bound to one transmitter module.

Follow the steps below to finish the binding procedure.

  1. Turn on the transmitter while holding the F/S button on the module (please refer to the module instruction manual for switch positions). Release the button. The RED LED on the XJT module will flash, indicating the transmitter is ready to bind to the receiver.
  2. Set X8R receiver in bind mode (see below chart for details), The RED LED on the receiver will flash, indicating the binding process is completed.
  3. frsky-x8r-led-signals-decoded.jpg
  4. Turn off both the transmitter and the receiver.
  5. Turn on the transmitter and connect the battery. The GREEN LED on the receiver indicates the receiver is receiving commands from the transmitter. The receiver/transmitter module binding will not have to be repeated, unless one of the two is replaced.

 Failsafe

Failsafe is a useful feature in which all controls move to a preset position whenever the control signal is lost for a period of time. X8R supports failsafe function for all channels.

Follow the steps below to set failsafe positions for each channel

  1. Bind the receiver first and turn on both the transmitter and the receiver;
  2. Move the controls to the desired failsafe position for all channels;
  3. Press briefly the F/S button on the receiver (less than 1 second). The Green LED will flash twice, indicating the failsafe position has been set in the receiver. 
  4. To disable the failsafe function, re-bind the receiver.  
  5. Failsafe is recommended to set when system is firstly used, or receiver has been re-bound. Follow steps below to set failsafe.

Option-1 How to set failsafe to a user-determined state on lost signal

  1. Bind the receiver to the transmitter module first and turn on both the transmitter and the receiver;
  2. Move the controls to desired failsafe position for all channels;
  3. Press briefly the F/S button on the receiver and you are done.

Option-2 How to set failsafe for no pulses on lost signal

  1. Turn off the transmitter, power on the receiver, and then press briefly the F/S button on the receiver.

 

Note: If failsafe is not set, failsafe default will hold last position before signal is lost. In this case, there exists

risk that your model will fly away or cause injury.

Additional Info

  •        Operating Voltage Range: 3.0V-16V (HV Version)   

  •        Operating Current: 30mA

  •        Specified Range: 1.5km-2.5km

  •        Resolution: 3072

  •        Latency: 22ms

  •        Number of Channels: 8CH

  •        Dimensions: 49mm×24.5mm×15 mm

  •        Weight: 14g

 

Reviews

Write Your Own Review

You're reviewing: FrSky V8FR-II HV long range Taranis 8/16Ch Rx receiver NO Telemetry

How do you rate this product? *

  1 Bone 2 Bones 3 Bones 4 Bones 5 Bones
Quality
Service
Value


  • + =

Why Buy From 2dogrc

Why Buy From 2dogrc

Most Products ship the SAME Day!

Have questions? Send us a quick email and we will get back to you fast!

High quality RC products from people who fly RC products!

Buy this product and earn Doggy Dollar loyalty points!